Myths, Facts, And The Truth About Silicone And Elastomeric Roof Coatings

If you believe you'll be saving the roofing decking plywood (not replacing it), then you might conserve yourself some clean-up difficulty by removing the components first and then peeling up the rubber! Detail of water damage on camper roofing system. More water harmed locations on RV roofing decking. There was nothing really dreadful that made me feel like I was going to fall through, however absolutely a great deal of damage and I was getting the feeling I would be changing a lot of the roofing system decking plywood.

Instruction Tips – Black Jack Coatings

Find Out Here Now: roof coating Tucson - DC Roofing of Arizona http://brooksgtfn606.xtgem.com/a%20coatings%20specialist%20explains%20how%20to%20correctly%20apply%20roof%20coating

I chose the most basic one initially, a vent cap from a kitchen sink plumbing vent pipeline. Starting to scrape caulk and sealant. I utilized a stiff scraper with a chisel-like blade and simply started prying and cracking and scraping and hacking. There is no other way around this, you just have to start digging until you expose the screw heads.

Loosening the screws in vent cap. The screws on this vent cap were hex-head metal screws so I used a small socket motorist to eliminate them. Some came out clean. Others were rusted and I had to utilize a vice-grip pliers to grab the heads and turn them bit by bit.

I found an old wasp nest inside the vent cover. This is a sight I'll most likely have actually to get used to, finding the remains of animal habitation in every nook and cranny. I spend an awful great deal of my time developing excellent wildlife environment in my yard so I don't get offended when a creature chooses to set up home in my Recreational Vehicle.

Luckily nobody was house in this old nest so I just tossed it. Perhaps I'll put a screen over it when changing it. Which brings us to the next point. You ought to try not to damage these pieces (like vent covers and caps) as you're scraping off the old caulk and sealant just in case you require to use them once again.

(Think I'll learn when the roofing system is done!) Prying up the vent cap and removing the last ring of rubber roofing system beneath. So I pried up the remainder of the cap and scraped up the remaining rubber roofing and butyl tape and putty and 25 years of other gunk and here's how it looks tidied up.

Myths, Facts, And The Truth About Silicone And Elastomeric Roof Coatings

One down, 7 more fixtures to go. Next I chose to tackle the only roofing system ventilation fan that my camper has. My roof vent also had a vent cover over it. So I began scraping the gunk from those screws. Beginning on the roofing system vent. Hardware exposed on roof vent cap, the very first nut came off clean.

Elastomeric Roof Coatings For Leaks Repair And Maintenace

Bolt is spinning. The fasteners on this RV roof vent cover were nuts on little bolts. The very first one came off great with an extension socket set. The second one just began spinning, implying the bolt was not repaired in place however turning together with the nut. Bummer. A peek at the hardware holding down the roofing vent cover.

I didn't have any excellent way to hold the bolt in place so rather I chose to saw through the bolts with a reciprocating saw. Sawing through bolts on roofing system vent cover. I used a cordless reciprocating saw with a metal-cutting blade however it was challenging to get the blade flat enough to reach the bolts so near to the roofing deck. Most were so old and rusted that they sheared off when I loosened then with a great deal of force. Loosening the brackets that held the vent cover in place. Then I scraped more caulk and roofing system sealant off the flange of the roofing system vent itself. I quickly discovered there were no more screws or hardware holding it down so I gave up on the scraping and went inside the Recreational Vehicle After scraping the caulk and sealant from flange of roof vent, no more screws! Unscrewing the inside cover plate of roof vent fan in Recreational Vehicle bathroom.

A couple sheared off with a great deal of force, but two would not budge. So I had to drill out the screw heads. I picked a drill bit near to the size of the shaft of the screws that I had already pulled out and began drilling. Picking a drill bit for drilling out a screw head.

Shatterproof glass suggested. So I drilled out the heads, one popped off and the other I was getting frustrated with and gave it a pull prior to it was drilled through. Instead of popping off the screw head, the plastic simply melted away around the hot screw head. Whoops. Hope I do not have to recycle this cover.

If not, I'll require larger screw heads when re-assembling. Cover plate removed from roofing system vent. Next I discovered little corner brackets with hex-head bolts holding them in. I unscrewed them (all came out fine fortunately) and pulled out the brackets and little white plastic spacers. Unscrewing corner brackets in roofing vent.

https://www.youtube.com/embed/79DHuaWZhsc

All corner brackets eliminated, all set to pull out. When the brackets were out I went back up leading to pry out the the roofing vent. Then I scraped up all the staying gunk and rubber roof. Taking off the old roof vent. There are two wires going to the roofing system vent (a black hot wire and a white neutral wire) that you'll need to clip to remove the old vent.