Consider An Elastomeric Roof Coating

If you believe you'll be conserving the roof decking plywood (not changing it), then you may save yourself some cleanup problem by getting rid of the fixtures initially and after that peeling up the rubber! Detail of water damage on camper roof. More water harmed areas on Recreational Vehicle roofing system decking. There was nothing really dreadful that made me seem like I was going to fall through, but certainly a great deal of damage and I was getting the sensation I would be replacing a great deal of the roof decking plywood.

Tips For Applying Your Elastomeric Roof Coating

Read More: how much does it cost to fix a roof https://pbase.com/topics/ceallava62/whatisar891

I opted for the most basic one first, a vent cap from a kitchen sink plumbing vent pipe. Beginning to scrape caulk and sealant. I utilized a stiff scraper with a chisel-like blade and simply started spying and cracking and scraping and hacking. There is no other way around this, you just have to start digging until you expose the screw heads.

Unscrewing the screws in vent cap. The screws on this vent cap were hex-head metal screws so I utilized a little socket motorist to remove them. Some came out clean. Others were rusted and I needed to use a vice-grip pliers to grab the heads and turn them bit by little.

I discovered an old wasp nest inside the vent cover. This is a sight I'll most likely have to get utilized to, discovering the remains of animal habitation in every nook and cranny. I spend a dreadful lot of my time creating excellent wildlife habitat in my yard so I don't get angered when an animal chooses to set up home in my Recreational Vehicle.

Thankfully no one was home in this old nest so I just tossed it. Perhaps I'll put a screen over it when changing it. Which brings us to the next point. You should attempt not to harm these pieces (like vent covers and caps) as you're removing the old caulk and sealant simply in case you require to utilize them once again.

(Guess I'll discover when the roof is done!) Prying up the vent cap and eliminating the last ring of rubber roofing system below. So I pried up the rest of the cap and scraped up the staying rubber roof and butyl tape and putty and 25 years of other gunk and here's how it looks cleaned up.

Foam Roofing Advantages: The Benefits Of Elastomeric Roof Coating

One down, 7 more fixtures to go. Next I chose to deal with the only roofing system ventilation fan that my camper has. My roofing vent also had a vent cover over it. So I began scraping the gunk from those screws. Starting on the roof vent. Hardware exposed on roof vent cap, the very first nut came off clean.

The Ultimate Guide To Rv Roof Coating

Bolt is spinning. The fasteners on this Recreational Vehicle roofing system vent cover were nuts on small bolts. The first one came off fine with an extension socket kit. The second one simply began spinning, suggesting the bolt was not repaired in place however turning together with the nut. Downer. A peek at the hardware holding down the roofing system vent cover.

I didn't have any good method to hold the bolt in location so rather I decided to saw through the bolts with a reciprocating saw. Sawing through bolts on roof vent cover. I used a cordless reciprocating saw with a metal-cutting blade however it was difficult to get the blade flat adequate to reach the bolts so near to the roofing system deck. The majority of were so old and rusted that they sheared off when I loosened then with a great deal of force. Loosening the brackets that held the vent cover in place. Then I scraped more caulk and roof sealant off the flange of the roof vent itself. I soon discovered there were no more screws or hardware holding it down so I quit on the scraping and went inside the RV After scraping the caulk and sealant from flange of roof vent, no more screws! Loosening the inside cover plate of roofing system vent fan in Recreational Vehicle bathroom.

A couple sheared off with a great deal of force, but 2 would not budge. So I had to drill out the screw heads. I selected a drill bit near to the size of the shaft of the screws that I had currently pulled out and started drilling. Choosing a drill bit for drilling out a screw head.

Safety glasses recommended. So I drilled out the heads, one popped off and the other I was getting irritated with and offered it a yank prior to it was drilled through. Instead of popping off the screw head, the plastic just dissolved around the hot screw head. Whoops. Hope I don't need to recycle this cover.

If not, I'll need broader screw heads when re-assembling. Cover plate eliminated from roof vent. Next I found little corner brackets with hex-head bolts holding them in. I loosened them (all came out great the good news is) and pulled out the brackets and little white plastic spacers. Unscrewing corner brackets in roofing system vent.

https://www.youtube.com/embed/spdYGUtZVcU

All corner brackets removed, ready to take out. As soon as the brackets were out I went back up top to pry out the the roofing vent. Then I scraped up all the remaining gunk and rubber roof. Raising off the old roofing system vent. There are 2 wires going to the roofing system vent (a black hot wire and a white neutral wire) that you'll need to clip to remove the old vent.